Home > Dell Error > Dell Error E2010 Memory

Dell Error E2010 Memory

E201E - POST Mem Test Causes: BIOS POST memory test failure. It has 2 Quad Core CPUs. If the issue persists, Contact Support as a memory replacement might be needed MEM0001 Multi-bit memory errors detected on a memory device at location(s) . Reseat the memory modules. Check This Out

Same as above. E1211 - ROMB Batt Causes: RAID battery is either missing, bad, or unable to recharge due to thermal issues. The System Memory section of the manual continues: General Memory Module Installation Guidelines: To ensure optimal performance of your system, observe the following guidelines when configuring your system memory… FBDs must If error remains, swap test the memory module by swapping the module with another identical module in the system, see if the error follows the module or not. http://en.community.dell.com/support-forums/servers/f/956/t/19467548

Each branch consists of two channels: Channel 0 and channel 1 are in branch 0. It can not boot, I have replacet memory, CPU, DRAC, the problem is the same. I agree with you - the best solution is to use the same size DIMMs in every slot.

E1210 - CMOS Batt Causes: CMOS battery is missing, or the voltage is out of acceptable range. No more error messages! If error remains, swap test the memory module by swapping the module with another identical module in the system, see if the error follows the module or not. Failing device is reseated/replaced/repaired.

Of course, the solution to make this warning go away was to simply put 8x2GB DIMMs in one server and 4x4GB DIMMs in the other (my smokin' hot former school teacher AC Cycle or SEL clear Any E2118 Fatal NBMemCRC High Northbound FBD CRC error on non-redundant entry. If the issue persists, Contact Support as a memory replacement might be needed E2112 Mem Spare Card # DIMM ##&## BIOS has spared the memory because it has determined the memory https://patrickhoban.wordpress.com/2011/03/25/2312/ N/A Any N/A E2013 N/A 0x83–BIOS failed to copy its flash image into memory.

Pingback: “Warning: The current memory configuration is not optimal.” « TheSaffaGeek() Tom Jobling Hi Steve - Thanks for the post. E2021 - Memory Population Causes: Incorrect memory configuration. If the issue persists, Contact Support as a memory replacement might be needed E2117 MemHot Plug Memory hot-plug operation has failed. Error detected during memory configuration.

N/A Any N/A E141F N/A 0xC4–Dell remote access controller (DRAC) configuration failure. If no card is present the .Card #. N/A Any N/A E1116 N/A 0x80–Interrupt controller failure. N/A Any N/A SBIOS N/A 0x05– BIOS shadow into memory.

x is the memory riser, A-Z. his comment is here Fitness. He enjoys listening to others' opinions before politely pointing out that they're completely wrong. | Read more Latest TweetsMy Tweets Get Blog Updates Enter your email address to subscribe to this Failing device is reseated/replaced/repaired.

System reset POST E2014 CMOS Fail High 0x84 -- CMOS failure. Failing device is reseated/replaced/repaired. System reset POST Special Exceptions - Message Code: "x10xx" Message Code Message String Message Priority Message Comments Minimum Action Required to Remove Message from LCD System Phase When Event Can Occur? this contact form How do you turned off the warning in every boot?

Moral of the story: go 1,2,3,4 and deal with the message or use DIMMs with matching sizes. One of the connections in the FBD link on the Northbound (towards the MCH) side is "broken". Reseat the memory modules.

AC Cycle or SEL clear POST, After POST E1711 PCI PERR B## D## F## High BIOS has reported PCI parity error on a component that resides in PCI configuration space at

Reseat DIMM One of the DIMMs in the set implicated by "## & ##" has had a MBE. string is left out of the message. E2022 - POST Fail Causes: General failure after video. http://binar.pl/p/poweredge-r310/poweredge-r310_tech_guide.pdf Look in section 8.1 (pages 36-37) for information on which RDIMMs or UDIMMs to use to obtain different memory configurations.

Any E1214 1.5VPwrGd High 1.5 VV voltage regulator has failed. Ray: The various articles are much appreciated, but it appears that #2... I'm still waiting to hear back from Dell, and I also posed the question to a mailing list of fellow Dell PowerEdge Linux admins, because even though it's not a Linux navigate here You know...

E2017 - Timer Fail Causes: Timer refresh failure. E1712 - PCI SERR B## D## F## PCI SERR Slot # Causes: The system BIOS has reported a PCI system error on a component that resides in PCI configuration space at Took quite a bit of digging but the link to the R310 Tech Guide helped. N/A Any N/A MEMC N/A 0x04–Memory Configuration.

If error remains, swap test the memory module by swapping the module with another identical module in the system, see if the error follows the module or not. Battery charges to > 24 hours of sustained charge. power supply fan failure or power supply over-temp). Inspect DIMMs.

Or at least that's my story and I'm sticking with it until Dell tells me otherwise; e-mail to them is out and I'll let you know if they say something different.